Powerlifting

How to Bench Press for Powerlifting: My Setup and Videos

My bench-press setup explained with training videos: rack height, grip, upper-back position, leg drive and complete sets, plus current competition rules.

A bench press starts before the bar leaves the rack. This is a walkthrough of the setup I used in the training videos below: equipment first, then grip and body position, followed by the unrack, descent and press.

The clips show my own gym practice, including 102.5 kg for two reps and 100 kg for three. For the longer story, my bench-progress article records my competition results and why I credit programming most for the improvement.

Competition update, September 2026: current IPF rules prohibit placing your feet on the bench during setup. Some of these older clips use that technique. Read section 4.2 of the current technical rulebook before using this footage to prepare for a meet.

Table of Contents

  1. Equipment Setup
  2. Lifter Setup
  3. Unracking
  4. Lowering the Bar
  5. Pressing the Bar
  6. Adding Repetitions
  7. Complete Sets and Next Steps

Equipment Setup

Spotter arms and a spotter

Before a heavy set, arrange suitable safeties and spotting. Check the rack and safety positions with a light bar before loading up; the numbered settings on one bench don’t transfer reliably to another.

These clips show me adjusting the spotter arms and a failed rep being caught by them. Equipment and technique reduce risk, but they do not guarantee that a failed lift will be safe.

Adjusting the spotter arms before lifting.
A failed gym attempt caught by the spotter arms.

If someone is spotting, agree the handoff and when you want assistance before the set. A spotter needs to pay attention throughout, including when the bar is returned to the rack.

A bench-press setup from my training archive.

Wrist wraps

The support shown here is a wrist wrap. In the original article I called these straps; wraps is the correct term for this equipment. They don’t replace a secure grip or a suitable load.

Putting on my wrist wraps.

Belt

A belt is optional in my gym setup. When I wrote the original guide I preferred benching without one because I found it got in the way of my arch. This older clip shows me trying a belt; it is a personal preference rather than an essential purchase.

An older training clip of benching with a belt.

Warming up

My warm-up in these sessions started with walking to the gym, followed by leg swings and band movements for my shoulders and lats. I then increased the weight over several bench sets.

For a planned working set of 100 kg for three reps, my example was:

Warm-up setWeightRepetitions
1Empty bar12
250 kg8
370 kg5
490 kg2

Those are the numbers from my training, not starting weights for a new lifter. The purpose was to arrive at my working sets prepared, without rushing straight to the heaviest load. Pain or difficulty controlling the warm-up is a reason to stop and reassess, rather than push through to the planned weight.

Lifter Setup

Bar height

I want to clear the hooks without losing my upper-back position or reaching excessively for the bar. In the original sessions I used setting 9 on that particular bench. Find the appropriate position on the equipment you’re using with a light bar and help from gym staff if needed.

Grip and wrist position

I experimented with a closer grip, with my little finger just inside the ring, and a wider grip with my index finger at the ring. The clips show both versions. My cue is to hold the bar securely and avoid letting it sit far back towards my fingers.

For IPF competition, use the required thumb-around grip within the 81 cm limit.

The closer grip I used in earlier training.
Experimenting with a wider grip.

Upper back and shoulders

After taking my grip, I draw my shoulder blades back and set my upper back against the bench. I think about keeping that position as the bar comes out of the rack, rather than doing all the setup and losing it during the handoff.

This clip includes the older setup described in the update above.

My upper-back setup in the older footage.

Feet, leg drive and arch

I used a modest arch in these sessions and placed my feet on the floor to create a stable position. The cue I used for leg drive was to push through the floor while keeping my upper back planted against the bench.

For IPF competition, maintain the required head, shoulder, buttock and foot contact, and meet the elbow-depth rule.

Foot placement and an arch in my older gym setup.

Bracing

Before unracking, I take a breath and brace so that my body is set for the lift. The point of the setup is to maintain control from the handoff through to the rack. Practise breathing and bracing with a qualified coach if you are unsure; a written cue cannot assess your individual technique.

Unracking

Once set, I lift the bar just enough to clear the hooks and bring it into position above my chest. My aim is a controlled movement that keeps the upper-back position intact.

For competition, wait for the Start command. These clips were recorded as gym training.

Bringing the bar out of the rack while keeping my setup.

Lowering the Bar

My preference in these sessions was a relatively quick but controlled descent towards my lower chest. I try to keep my upper back in position rather than relaxing as the bar comes down.

For competition, hold the bar motionless on the chest or abdomen, meet elbow depth, and wait for Press.

The descent in one of my training repetitions.

Pressing the Bar

I press while keeping my feet planted and my body position stable, then finish with straight arms. In a meet, wait for Rack before returning the bar.

Pressing the bar back to the finished position.

Adding Repetitions

The video below shows a set of repetitions. I want the setup to remain recognisable across the set; if I lose control or need assistance, that is the end of the attempt rather than a reason to force another rep.

The sets and repetitions belong to the wider programme. I discuss why programming helped my bench most separately from these technique clips.

Several repetitions from a gym set.

Conclusion

Here are two full examples from my training: 102.5 kg for two reps and 100 kg for three. They bring the setup and movement into one sequence, so you can compare them with the individual clips above.

102.5 kg for two repetitions in training.
100 kg for three repetitions in training.

For the results behind the videos, read my bench-progress timeline. For the experience of taking training onto the platform, see my first-meet account. My squat guide covers the other lift in its own article.

Competition rules checked against the IPF Technical Rulebook effective 1 March 2026, version 3, section 4.2. Other federations may use different rules.

Lift & Nourish app

Log the sessions you read about.

A gym log and food diary for iPhone and Android, with a 7-day free trial.